A fun mini drone with all of DJI's signature technologies. Spark; Phantom Series. Professional-grade aerial imaging. Naza-M Lite IOC and attitude stabilization; great for entry-level systems. Naza-M Lite Release Notes 2014-04-22. Naza-M Lite User Manual 2.00 2014-04-22. Naza-M Lite Assistant Software. DJI's cost-effective NAZA-M Lite flight control system is a simplified version of the NAZA-M. It features the same high reliability and stability of the NAZA-M, but is tailored to entry-level enthusiasts with an innovative all-in-one design that simplifies installation, while saving space and weight. Motors and ESCs in DJI multi-rotor kit are recommended. Please make sure you are using the ESCs and motors recommended by the manufacturer of your multi rotor first. NAZA-M LITE output is 400Hz refresh frequency. Connect all ESCs to MC by the motor numbering method introduced in Multi-Rotors Supported of Appendix. If you use 3.
Advertising
©2014 DJI. All Rights Reserved.
NAZA-M LITE
User Manual
V 2.00
2014.04.21 Revision
For Firmware Version V1.00
& Assistant Software Version V1.00
For Firmware Version V1.00
& Assistant Software Version V1.00
Thank you for purchasing this DJI product. Please strictly follow these steps to mount and connect this system on
your aircraft, as well as to install the Assistant Software on your computer.
Please regularly check the NAZA-M LITE web page at our website
information, technical updates and manual corrections will be available on this web page. Due to unforeseen changes
or product upgrades, the information contained in this manual is subject to change without notice.
* This manual is only for basic assembly and configuration; you can obtain more details and advanced instructions
when using the assistant software. To assure you have the latest information, please visit our website and download
the latest manual and current software version.
If you have any problem that you cannot solve during usage, please contact your authorized dealer.
www.dji.com
Advertising
Popular Brands
Popular manuals
Advertising
©2014 DJI. All Rights Reserved.
8
Assembly
接电调
接云台
F1
F2
接电调
接云台
VU
·
Do not mount it on any other electronic devices. Make sure You can see the
LED light during the flight.
LED light during the flight.
·
If use with DJI multi-rotor, you can solder the VU power cable to power
pads on frame bottom board. Please refer to DJI multi-rotor manual for
details.
pads on frame bottom board. Please refer to DJI multi-rotor manual for
details.
·
If use with 3
rd
part multi-rotor, you can make a connecter by yourself to
connect VU, ESCs and battery.
·
Sufficient air flow over the VU is highly recommended.
MC
·
Please use
3M gummed paper provided To mount MC, and mount MC parallel to the
aircraft horizon.
·
The output ports of MC (the right side in figure) should point to the front of
multi-rotor. You
multi-rotor. You
’d better put MC at the gravity center of multi-rotor. Please
make sure all ports are accessible when installing the MC so as to facilitate
wiring and software configuration.
wiring and software configuration.
·
In three-pin ports, pins near the nicks are signal pins.
·
After choosing a location to mount the MC, it is recommended
that you DO NOT mount the MC until all wirings and software configurations
are completed.
are completed.
GPS/COMPASS
Dji Naza Lite Manual
·
GPS/Compass is sensitive to magnetic interference, should be far away from any electronic
devices.
devices.
·
You should use epoxy resin AB glue to assemble the GPS bracket first as the figure showed
in previous page.
in previous page.
·
Mount the bracket on the center plate of craft first, then fix the GPS on the plate of the
bracket (by 3M glue provided). The GPS is sensitive to vibration interference, so position
the bracket at least 10 cm from any rotor.
bracket (by 3M glue provided). The GPS is sensitive to vibration interference, so position
the bracket at least 10 cm from any rotor.
·
The DJI logo marked on the GPS should face the sky, with the orientation arrow pointing
directly forward. The GPS/Compass is packaged with a special indication line for mounting
for the first time.
directly forward. The GPS/Compass is packaged with a special indication line for mounting
for the first time.
·
If you are uncertain whether materials near the GPS/Compass module are magnetic or not,
you can use a compass or magnet to check it. If you use your own mounting rod, make sure
it is NOT magnetic!
you can use a compass or magnet to check it. If you use your own mounting rod, make sure
it is NOT magnetic!
Aircraft Nose
R/C System
These are example connections. Please
setup Aileron, Elevator, Throttle, Rudder
channels on your TX first, and choose
o n e 2 positions switch/channel ( 3
positions switch with GPS) as control
mode switch, then connect your receiver
to the right ports on MC.
setup Aileron, Elevator, Throttle, Rudder
channels on your TX first, and choose
o n e 2 positions switch/channel ( 3
positions switch with GPS) as control
mode switch, then connect your receiver
to the right ports on MC.
R/C Receiver
(JR)
(JR)
RUDD
THRO
AILE
ELEV
R/C Receiver
(Futaba / Hitec)
(Futaba / Hitec)
1
2
3
4
3
4
Futaba S-Bus
S-Bus
2/3-position switch channel
Optional
ESC
M1-6
To Battery
ESCs, Motors
·
Motors and ESCs in DJI multi-rotor kit are recommended.
·
Please make sure you are using the ESCs and motors recommended by the
manufacturer of your multi rotor first. NAZA-M LITE output is 400Hz
refresh frequency.
manufacturer of your multi rotor first. NAZA-M LITE output is 400Hz
refresh frequency.
·
Connect all ESCs to MC by the motor numbering method introduced in
Multi-Rotors Supported of Appendix.
Multi-Rotors Supported of Appendix.
·
If you use 3
Naza M Lite Manual
rd
party ESCs, please make sure the ESCs travel midpoint is at
1520us. DO NOT use 700us travel midpoint ESC, as it may lead aircraft to
fly away or cause injury and damage. After connect ESCs to motors,
calibrate all your ESCs one by one through the receiver directly before
connect them to your MC, Make sure program all of them into Governor off,
Break off and Normal Start up to get best experience.
fly away or cause injury and damage. After connect ESCs to motors,
calibrate all your ESCs one by one through the receiver directly before
connect them to your MC, Make sure program all of them into Governor off,
Break off and Normal Start up to get best experience.
Dji Naza Manual
Roll
Pitch
2/3-position switch channel
Dji Naza Lite Manual
Important: the continuous
output of the V U is 3A@5V, and the
maximum instant current is 7.5A. If the V U
cannot afford the working current for you r
servos, please use an independent power
supply; otherwise, it may cause the V U
safeguard and lead to the main controller
reboot.
Advertising
Popular Brands
Popular manuals